Nyx help...

signup1970 · Post by **signup1970** » Thu Jul 10, 2008 8:34 pm

I've uploaded a pic. Then in the visual tab I hit new page it comes up as start#. Added text "Hello". Hit the save button and then the preview tab and nothing displays. The console:

16:30:24.833: Error: Action not found: start
16:30:24.833: Running action start...
16:30:24.832: MetaInfo loaded.
16:30:24.559: Script loaded.
Milovana FlashTease Engine ready...

Obviously missing something. Is there a help section or a "Getting Started" page for Nyx yet? Also, does anyone have about three sample pages I can throw in the Script section to play around with?

BTW: Mac/OSX/Firefox 2

Thanks.

eteased · Post by **eteased** » Thu Jul 10, 2008 9:57 pm

I have pretty much the same issue. See my "Problems saving in NYX" post in the Tech Support forum.

Here are a few pages of script from one of my earlier teases that worked:
10#page(
'<TEXTFORMAT LEADING="2">First question! Choose the words below that properly complete the following sentence:</TEXTFORMAT><TEXTFORMAT LEADING="2"></TEXTFORMAT><TEXTFORMAT LEADING="2">I want to see what __________ cock looks like when __________ really horny! Pump it fast and hard for me! </TEXTFORMAT><TEXTFORMAT LEADING="2"></TEXTFORMAT><TEXTFORMAT LEADING="2">A. your, your B. you're, you're C. your, you're D you're, your</TEXTFORMAT><TEXTFORMAT LEADING="2"></TEXTFORMAT><TEXTFORMAT LEADING="2">Follow the instructions, then pick the best answer. Use the pen & paper to note down how many times, if any, you get each question wrong.</TEXTFORMAT>',
pic("1-3.jpg"),
buttons(11#, "A", 11#, "B", 12#, "C", 11#, "D")
);

11#page(
'<TEXTFORMAT LEADING="2">Uh-oh, that's not right! You're not getting off to a very good start here. Put a clothespin on each nipple and wait for the timer to run out. If you've missed this question more than once, tug and twist on the clothespins while you wait. Be sure to note down on the paper how many times you've answered a question incorrectly.</TEXTFORMAT>',
pic("1-1.jpg"),
delay(90sec, 10#)
);

12#page(
'<TEXTFORMAT LEADING="2">Very good! I'm glad to see that you understand the difference between "your" and "you are." As a reward, I want you to drip some lube over just the head of your cock. Now spend some time smearing it around! Don't touch the shaft, though. You can imagine that the nice young girl in the picture is letting you slip just the very tip of your cock into her very warm, wet, tight little pussy.</TEXTFORMAT>',
pic("1-4.jpg"),
go(13#)
);

Post by **seraph0x** » Fri Jul 11, 2008 7:42 am

signup1970 wrote:I've uploaded a pic. Then in the visual tab I hit new page it comes up as start#. Added text "Hello". Hit the save button and then the preview tab and nothing displays.

*Should* work. Try giving him a couple seconds time to save the script before switching to the Preview tab. Even better - use the "Save and Preview" button which will wait just long enough.

Post by **seraph0x** » Fri Jul 11, 2008 7:43 am

eteased wrote:I have pretty much the same issue. See my "Problems saving in NYX" post in the Tech Support forum.

Try again now please.

signup1970 · Post by **signup1970** » Fri Jul 11, 2008 4:22 pm

Nope. However, now I get a quick pop up when I open a tease saying 'Loading tease details". But, info is still not being saved. Same error from the step I described above as well.

BTW thanks for the code eteased.

eteased · Post by **eteased** » Sat Jul 12, 2008 8:11 pm

signup1970, try creating a new tease from scratch and see if that works. The one that I was having trouble with still wasn't working. So I finally deleted it and created a whole new one. That new one seems to be working fine.

Nyx help...

Nyx help...

Re: Nyx help...

Re: Nyx help...

Re: Nyx help...

Re: Nyx help...

Re: Nyx help...