You should be using 12V power supply, not 24 (as with 24 amp works at full power). Let me say first that edger477 is extremely knowledgeable and helpful. He guided me thru my first DIY build and always look to him for tips to improve my setup. Saying that, my experience with power supplies is diffe...

How does it feel? Is it genuinely pleasurable, or is it more of a weird sensation that you grow to enjoy? Basically I'm 50/50 on buying some kit, but it's not cheap. I don't really want to go DIY, so convince me it's worth it! Don’t believe there is a 100% same experience or guarantee regarding e-s...

Thanks for the update. This will be my next project. I plan on taking a slightly different approach. Will use the same Douks amp as you but will have two identical DIY boxes, mainly because I already have a working two channel system that has switches on the input side to swap channels and switches ...

Been a couple of months since last post. Curious about your experience / satisfaction with the new box. Any surprises or advice for others considering doing this? Does it meet your expectations? Thanks!

I don't own a Coyote so cannot provide an informed opinion on that device. It looks interesting and appears to be an excellent value for what it offers. I did recently assemble a DIY stereostim box using the design based on " Tronic's MidiStim " https://milovana.com/forum/viewtopic.php?t=2...

...once conductive silicone tubing has some age. My experience is that CR is not very efficient. For that reason, I tend to prefer to use TENS pads when possible. Also, I will trim a 2" square pad to appx 0.75" wide (still 2" long on axis with the electrode wire) which helps to focus...

Thank you both. Didn't know that was how it worked. Did receive response from one member over night.

Relatively new member here. Attempted to send PM's to users who have exchanged with previously. They are still in OUTBOX. Attempted to send PM to board administrator to report / inquire. That is also now in my OUTBOX. Is there a problem? Can't think of anything I have done which would put me in &quo...

Hey everyone, had my build up and operational but the aux port on my amp has just stopped working, the bluetooth still works and all of the wiring has been tested, the problem is isolated to the port. This is the amp i'm using https://www.amazon.co.uk/gp/product/B083QF164T/ref=ppx_yo_dt_b_asin_titl...

aelskling wrote: ↑Sat Aug 27, 2022 2:25 pm
Easiest way ist to just play the online EOS version: https://milovana.com/webteases/showtease.php?id=37050

No GuideMe needed for that.

Duh... skipped right over that. Thanks...like a I said...NOOB here.

NOOB here so please bear with me. I just built a stereo stim box (thanks to these forums) and would like to try my first tease but real learning curve here. The Estim Tower keeps popping up so must be a good one? Initially unsuccessful because I don't have Adobe Flash Player.but kept reading and fin...

First opportunity for an extended session this afternoon. Doubt that my TENS 7000 will be getting a lot of use going forward :-D. Very pleased with the results. Ran it about an hour and didn't observe any excessive heat. The 4 ohm resistor was a little warm to the touch but nothing to be concerned a...

Finally rec'd basic components for this project over the weekend and did brief initial run this morning. Everything worked but had a couple of surprises (nothing bad). More on that later. Did not attempt to wire anything permanently or mount in a box. All connections made with wire nuts and patch co...

I used these: https://www.amazon.de/-/en/gp/product/B07G5KB51M I did not use them for the purpose you are using them (I tested my amp and it does not produce spike on either on or off, so I do not need switch to disable output), but for polarity switch - these 6-contact switches have 3 positions - ...

Have question regarding proper implementation of an output switch. My build will include the two 10 ohm resistors installed parallel to the transformer. I want to install a simple toggle on/off in line switch between the transformer output and the electrodes. Reasoning is that I want to prevent the ...