Building a male sex machine
Posted: Sun Jan 05, 2014 4:45 am
So I'v had this idea long time ago. To build a sex machine for myself. The problem here is that market doesn't seem to offer ANYTHING good. What is there looks not very convenient, not really well-made, and above all - overpriced as hell.
So I'v been planning it up for a few years now, and here's what I came up with.
1) It will be a tube, inside which a fake pussy moves up and down by a motor.
2) It should be low voltage to rule out any possibility of damage, because I don't have skills needed to make it safe otherwise.
3) It should have speeds ideally from 30 strokes per minute to 180, controllable.
Now, here's the plan:
1) As a fake pussy the best option I see is Fleshlight Sex in a Can series. They are not too large, provide good sensation, they are easily shaped = can be easily held in place by a holder.
2) For the device itself I am thinking of using plastic water pipes of different diameter. 2 pipes in total:
- 1st pipe is for holding the fleshlight. Inner diameter is the same as FL to hold it steadily. This pipe would be moving inside the second pipe which is the outer shell of the device. Sturdy plactic, about 2mm thick (or even 1mm if it's sturdy enough)
- 2nd pipe is the outer shell of the construction. It's inner diameter is slightly larger than 1st pipe's outer diameter, to rule out friction. Good thick sturdy plastic.
3) It all is moved by a motor that is places in the far end of the 2nd pipe. The motor... is a problem.
Way I see it it should be a gear motor that will rotate a circle to which an arm is attached. Arm is extending and retracting a small pole that is attached to the 1st pipe, moving it up and down.
Now, why do I write this thread?
First, to share an idea.
Second - to receive criticism from more knowing people.
Third - to ask for help with the motor.
As I said it should be low-voltage. It should however be powerfull enough to be able to lift about 1.3 pounds (the weight of fleshlight).
But there comes a problem. I don't know what to choose! How do I calculate the needed torque of the motor? How do I find the one with variable speeds? The only thing I can judge right now is pretty much only voltage and size.
And where do I look? I know a lot of enthusiasts assemble ROBOTS, but I don't even know where to get a small but powerful motor.
So... Help?
So I'v been planning it up for a few years now, and here's what I came up with.
1) It will be a tube, inside which a fake pussy moves up and down by a motor.
2) It should be low voltage to rule out any possibility of damage, because I don't have skills needed to make it safe otherwise.
3) It should have speeds ideally from 30 strokes per minute to 180, controllable.
Now, here's the plan:
1) As a fake pussy the best option I see is Fleshlight Sex in a Can series. They are not too large, provide good sensation, they are easily shaped = can be easily held in place by a holder.
2) For the device itself I am thinking of using plastic water pipes of different diameter. 2 pipes in total:
- 1st pipe is for holding the fleshlight. Inner diameter is the same as FL to hold it steadily. This pipe would be moving inside the second pipe which is the outer shell of the device. Sturdy plactic, about 2mm thick (or even 1mm if it's sturdy enough)
- 2nd pipe is the outer shell of the construction. It's inner diameter is slightly larger than 1st pipe's outer diameter, to rule out friction. Good thick sturdy plastic.
3) It all is moved by a motor that is places in the far end of the 2nd pipe. The motor... is a problem.
Way I see it it should be a gear motor that will rotate a circle to which an arm is attached. Arm is extending and retracting a small pole that is attached to the 1st pipe, moving it up and down.
Now, why do I write this thread?
First, to share an idea.
Second - to receive criticism from more knowing people.
Third - to ask for help with the motor.
As I said it should be low-voltage. It should however be powerfull enough to be able to lift about 1.3 pounds (the weight of fleshlight).
But there comes a problem. I don't know what to choose! How do I calculate the needed torque of the motor? How do I find the one with variable speeds? The only thing I can judge right now is pretty much only voltage and size.
And where do I look? I know a lot of enthusiasts assemble ROBOTS, but I don't even know where to get a small but powerful motor.
So... Help?