Page 2 of 2

Re: [QUESTION] E-STIM blue balls

Posted: Fri Sep 03, 2021 2:23 am
by zebbg69
throwawayacct wrote: Thu Sep 02, 2021 6:13 pm I'm a big believer in insulating the top half of a rubber loop electrode.
I have been doing that in various forms ever since I saw your advice on SocialStim. Thanks for that!

As for the tightness, the head loop is the challenge for me. Since I am starting out soft, it has to be quite tight to feel good, but that becomes *too* tight quickly when things get going. The answer has been to put some play in the system. My best head loop so far is a wire-core CR in a figure-eight with the main loop around my head and the smaller loop free to contract as I expand--the wire gauge is critical, 16 AWG I think, might be 18. I bend the free loop down so it rests against my head surface--seems a shame to waste it.

I also had promising results with another wire-core CR bend using 14 AWG, which only BARELY fits into the 2mm CR tunnel and is stiff enough to really hold a shape. I was going for an incomplete head loop with a gap and some "wings" at the gap that I could loop closed with self-clinging cloth medical tape. It felt great, but my first design was not viable to wear for a full session. With some refining, it could be the best yet, owing its success to the cloth tape's comfortable stretch.
throwawayacct wrote: Thu Sep 02, 2021 6:13 pm I was using J-Lube for a while... I discovered "K-Lube" and it seems to last longer, and mixes easier, and less residue on cleanup.
K comes after J, is that it? :lol:

Re: [QUESTION] E-STIM blue balls

Posted: Fri Sep 03, 2021 7:46 am
by MrGoGoGirl
zebbg69 wrote: Fri Sep 03, 2021 2:06 am When I got my BTStim in 2018, I also bought what Current Pleasures calls the Double Bullet. I don't know who manufactures it, but it is for sale on many sites. The whole surface is aluminum, with the tip isolated from the base, which means it can "ghost fuck." It immediately supplanted the PES, even though its 1.5" diameter takes some effort to insert (when unaroused which unfortunately is how I normally start), where the PES at 1" or so pops right in. The Double Bullet's metal base is a delightful rimmer too, so the extra effort is well worth it, and I have only gone back to the PES a couple of times for novelty. Pro tip: to get ghost-fucked, don't sit with all your weight on the plug.
can you please link this or post a picture? i searched but I still have no idea what this is :D

Re: [QUESTION] E-STIM blue balls

Posted: Fri Sep 03, 2021 8:09 pm
by doremi
blondie88, I guess that a signal wave graph from a scope might help a lot if you can compare it with others who enjoy their device and settle this one and for all. However, that's not an inexpensive piece of equipment.
:clover:

Re: [QUESTION] E-STIM blue balls

Posted: Fri Sep 03, 2021 11:57 pm
by zebbg69
MrGoGoGirl wrote: Fri Sep 03, 2021 7:46 am
zebbg69 wrote: Fri Sep 03, 2021 2:06 am When I got my BTStim in 2018, I also bought what Current Pleasures calls the Double Bullet...
can you please link this or post a picture? i searched but I still have no idea what this is :D
The "Double Bullet" at Current Pleasures, your ghost-fucking friend and rimming companion:
https://www.currentpleasures.com/produc ... 2-5mm-plug

Minor warning: the build quality of its 2.5mm connector was questionable, and mine had an intermittent connection. I cut off the connector and twisted the wires onto female pin jacks (cut off from a Y-connector), then encased the joints in heat shrink. It's been perfect ever since.