Milovana.com

What about using a rubber liner for Venus2000 instead of a loo roll? The liners are available in various diameters: http://www.venus2000.de/zubehoer.htm

Also, I wonder if the Humpus Sex Machine could be turned into an automatic edging machine. The toy is equipped with a remote control that may be connected to the Arduino board. What do you think?
http://www.humpus.com/index.php?route=common/home

This is great stuff; However I would like to get some more advanced stuff. I am using a venus 2000 troughout my selfbondage sessions. So far I am using different timers to deny myself an orgasm. However the arduino board plus the software could help a lot. is it possible to let the arduino switch the venus machine on and off? I also read about an anal pressure sensor that could be used to detect the closing in of an orgasm, since the sphincter muscle will involuntarily contract.

Does anyone have an idea how to connect these ideas?

Regards hotiger

Hi again

I posted a while back and told how I made one as well and it works quite well, I sorted the over stimulation problem by increasing the delay time from the edge - stop to restart of the vib I like it alot and can edge for ages.

Since then I have gotten into 3D printing in a big way, there are loads of things you can use a 3D printer for and I have printed for myself a chastity device, which is fun. Its here if anyone is interested. http://www.thingiverse.com/thing:940729.

Then I saw this post.. viewtopic.php?f=12&t=19339.

Well I thought how wicked would it be to combine the edging machine with a chastity device..A device that will keep you on edge and keep you locked up at the same time..Hmmmmm...all the dom would need is an on off switch..no cumming and no touching while continually close to an edge..insane right

I am working on combining the two now.

Watch this space

Bill xxx

I have taken a Venus receiver in it's original form and adde a few parts (upgrades?).

1. A rod and a linear bearing to make it work even when I go limpy. Like this.
http://www.pornhub.com/view_video.php?v ... 5ce7ec7b04

2. Then I added a thin pad inside the receiver on the top and bottom of my penis. Each was connected through a rod to a speaker. One on the left and one on the right. I did it in a way that I retained a seal into the receiver and made the connecting rods long enough to not effect it going up and down!

3. Play my favorite Cock Heros like anything AwesomeX or Island! Loudly.

4. Lean back and take the awsome torture.

Future upgrades.
1. Stroke speed control. I have a bunch of Arduino stuff and I know how to use it! Just need time.
2. Stroke length and receiver position sensors. Got'em in my collection.
3. Various counters and timers. Just programming.
4. Other sensors. ??????
5. Retension devices. Electric locking controls. Maybe not
6. Valves to allow missing strokes for those 123-123- rythms. I love this rythm when I stroke manually.
7. Perhaps some related e-stim. Tests are positive so far.

Now the best part, Gemcutter released a PMV with all the action matching the beats!! Perfection.
http://www.pornhub.com/view_video.php?v ... c6f1762fdf

Lots to do and so short a time I have.......

hotiger wrote: ↑Mon Aug 03, 2015 10:28 pm This is great stuff; However I would like to get some more advanced stuff. I am using a venus 2000 troughout my selfbondage sessions. So far I am using different timers to deny myself an orgasm. However the arduino board plus the software could help a lot. is it possible to let the arduino switch the venus machine on and off? I also read about an anal pressure sensor that could be used to detect the closing in of an orgasm, since the sphincter muscle will involuntarily contract.

Does anyone have an idea how to connect these ideas?

Regards hotiger

Hi,

I'm new to this forum, so apologies for any protocol errors!

I have built a device using an Arduino that might do the trick, although I'm not sure about how the Venus 2000 is controlled. In it's present form it can sense PC muscle contractions from a butt plug and turn off stimulation (currently with a vibrator attached to a cock ring) if it senses any contractions. Usually those happen when you are particularly turned on, and uncontrollably at orgasm - although to be fair, it can't stop you orgasming at the moment... but makes the build up very prolonged and switches off completely as you are closing in.

Hi Jamesdeville,

great, sounds just about like the stuff we are so desperately looking for ;) the arduino would have to shut off ac power to the venus to stop stimulation. Would your device be able to do that? I am very interested how you did the measuring

This is Great stof.
I have now built this but added Adrino Relay to this becouse as [email protected] say the motor is not
very powefull and I could not cum with this little motor. I use this to start and stop my e-stim device.
It is working and I have now manage to get my first "Denial Cum".

If any is intetresting in how this is done. I will send info on this.

Thanks denial1234 for your super setup and program.

Hi Puste,

would realy like to know more about. Could you send me details?

Thx Jerry

puste wrote: ↑Sat Jan 26, 2019 6:52 pm This is Great stof.
I have now built this but added Adrino Relay to this becouse as [email protected] say the motor is not
very powefull and I could not cum with this little motor. I use this to start and stop my e-stim device.
It is working and I have now manage to get my first "Denial Cum".

If any is intetresting in how this is done. I will send info on this.

Thanks denial1234 for your super setup and program.

I'm also interrested, maybe you can make a good manual instruction pdf like on the first page

Sory for delay.
I have now try to do a drawing of what I have done. It is not so different from [email protected] design.
It use same programming. But I have change some lines in the code only to clear out what is done.

When using this i can say that it is still in some test stage and there is a lot to be done.
This is the first time I've been working with Arduino Uno. But I am a programmer so a do know
some about programming. Sorry for my spelling english is not my home language.

when using this setup I have used it with an ET312B ESTIM Device.
And I use it most often together with SmartStim 4.
The E-stim file I have found is Tjenkins-i will come. This contains many different E-Stim effects and
is perfect for this setup.

I've found that if you add a 47uf to the schematic then it works much better. You can se more about this in this video.
https://www.youtube.com/watch?v=pYDHbLtzT_c
I do not know why in this video he has placed a 10 KOhm Resistor.
I use 2 MOhm for best sensitive.

Another thing i have done is placed a ADHESIVE RUBBER FEET on to the Flexiforce pressure sensor.
Remember it has to be hard or it will not work. But this give more presure on the sensor.

if others have made some changes, I would like to hear about this.....

I have now made some change to the original program. So it works better with E-Stim.
Sorry I could not add txt file in milovana. I will try to link to it when uploaded to another place.

I have also made a wav file to use with E-Stim. But i have to do some test before I upload this.

Now I have created a PCB for this. I will return when I have made a test.
But for now here is a picture of the PCB board, It should fit eksact on Arduino.

Also I have found out that 47uF is to high. In stead I have change this to 4,7uF.
It is working perfect with 4,7uF, and with this new board it can only be better.

Now i simple give up the project becouse of problem with E-Stim device interference with the Flexiforce Pressure Sensor.
When just turning Estim device a little up the Flexiforce Pressure Sensor goes crazy.

You really dont need to build a edging machine for e-stim, unless you dont have means to play audio through it.

There are tons of edging estimaudios out there that are just excellent at making you edge over and over.

I got one named "rollingprecummer", if I set this up on medium volume, i wouldnt come in 10 hours of stimming, but I would have an edge about every 30-60sec. Turn the same file up to 100% volume i would eventually come, with alot of struggle and also maybe ruin it depending on where the audio is at the moment