This Robot Sex Machine is awesome! clearly for a higher budget than the CMMachine. If you haven't seen it yet the creator has a video where it explains the software and also includes the parts list for a DIY:
There is a github repo. which has some "funscript" files on there with all the timings. Now, just to do some maths / method(s) of converting and calculating how fast the motor needs to be at just before.
My Tremblr can do about 180 strokes / minute (it can go quicker I believe) but not much quicker. Ideally would just need to work out the motor speeds to strokes / second. I already have a way of sending 0-100% speed over. Just need to work on the calculations.
If using a V2K or Tremblr, do you run continuous at adjusted speeds or can you do the 3 strokes followed by a skip (or other intermittent) stroking pattern? I have a homemade machine like a V2K but it suffers ramp up and down of speeds. And the faster the worse.
I have some material collected to make a continuous pump interface to a set of valves but not enough time to quit fapping and get to it! If this idea worked you could have any pattern you wanted that you could code.
Im currently working on an automated V2K project. I replaced the speed control knob with a pully added a belt from that to a stepper motor and with that I can program different speeds at set times using an Arduino.
I started the project knowing very little about programming or electronics so its been a long, slow journey but Im almost finished with it. Ive added a 2nd stepper that when rotates a few steps one way or the other presses down on the stroke length buttons so I have automated controls of that too. I've also have an IR sensor that straps on behind your balls and picks up when the PC muscile flexes. This can be used to set the speed to stop for however many seconds if your in edging mode, or it can be used to detect if your cumming and set the stroke length to the shortest so when you go floppy it can keep stroking without you falling out if you want to be in endless milking mode. The sensor works well but its not perfect, you have to be still because if the sensor moves it will see that as a spike and trigger an action. Its best used in a bondage setup where your strapped down and kept still.
Im currently working on adding a button controlled lube setup for this. I have a tube going into the end cap of the stroker (I carefully melted the cap with a lighter and pushed it through while it was still hot and malleable) thats connected to a 12v peristaltic pump thats connected to a motor driver and then to another Arduino. Then Im going to add some buttons to turn it on so you can add lube mid session. Maybe 1 button to add lube every 5 mins and another to add lube right now. This I feel is important for self bondage setups.
The whole setup works very well so far and while there is a little bit of ramp up and down on speed change I find its very minimal on the V2K. In terms of timing it up to CH Videos I find its best to pick what speeds on the V2K you feel are slow, normal, fast, vfast, super fast, omgfast and code to those positions. Just use the video as a guide rather than trying to match the strokes exactly because while it is mostly possilbe to match them it would take weeks to time up a single video. And thats the other draw back with my setup so far. Everything has to be manually timed and coded. I've got it to a point where its as simple as saying at this time go fast at that time go slow or at this time start this loop to run speed patterns. But it still time consuming, I can maybe do a 1hour video in an afternoon now. I tend to turn the volume of the video off and crop the image so its just the beat timer as to not spoil the show for later.
Once I'm done with the lube controls and made a few more tweeks I'll post more about this in the Hardware & Teledildonics section. Its not a cheap project and you'll ideally want a 3D printer as well to replicate it.
All these projects are very helpful getting this type of entertainment to the public, at least a certain part of the public.
hosenguy wrote: ↑Tue Aug 21, 2018 2:02 pm
And thats the other draw back with my setup so far. Everything has to be manually timed and coded. I've got it to a point where its as simple as saying at this time go fast at that time go slow or at this time start this loop to run speed patterns. But it still time consuming, I can maybe do a 1hour video in an afternoon now. I tend to turn the volume of the video off and crop the image so its just the beat timer as to not spoil the show for later.
I am very excited with the work of qdot and liquid and the stuff listed in this post. Their are many already sync'd videos for several types of commercial products and these guys are making an open sourced interface to use them to control a variety of machines. (Some programming required.) This is going to get better and better sooner and sooner! viewtopic.php?f=25&t=20995&p=251468&hil ... ug#p251468
I've managed to sync the tremblr with syncydink (one beat == 1 linear movement (Shaft to Top)) so 2 beats == 1 stroke. I don't know how in sync it stays with a chamber attached, as I've only done a dry run without, so that may change. The stroke of the motor stays in sync though currently. Also my Tremblr seems to be able to do 3.75~4 strokes / second so anything higher than that on cock hero and it'll of course be out of sync a little until the beat slows down. But again, under load them figures may change.
Going to do another run later, and all being well I'll publish a video.
But yeah, it's not specifically for penile stimulation (you can attach fleshlight or whatever, but I don't feel like it is built for that as much (but surely does work for hands-free experience).
Maybe it saves some time and gives clarity to some.