so I basically want to lift some weight up and down repeadedly on about 3cm arm (6cm total height difference between lower and higher points). The weight is about 3 killogramms, arm is 3 cm, as I said, so I need torque of about 9 kg*cm? 10-11 to be sure, right? Nezhul, There's an important consider...

The vibrators ran off of 3 1.5v LR44 button cell batteries. My power supply is adjustable and can give anywhere from ~9.4-14v up to 150W. At its lowest voltage setting, a PWM duty cycle of around 50% should give close to 4.5 volts(assuming I understand electronics as well as I think I do :-/ ). One...

<snip> What I am currently looking into is the Real Touch. http://www.realtouch.com <snip> With that being said, since the realtouch already has a computer interface, is there perhaps some way to control this thing programmatically? In turn, that could be made into an API to control over the intern...

    <snip> notes: - I measured the resistance of my bullet vibrators to be about 13.4 Ohms, which at 4.5v will pull 335.8mA - The vibrators got very hot after running for a long time. @Bundle, You're probably putting too much current through your vibe's motor; that's why it's getting hot. Motors ar...

RealTouch is awesome. I don't think it will actually be much harder than a development path for females. The general start/stop/change speed commands sent to a vibrator shouldn't be much different than the commands of RealTouch, so conversion shouldn't be too difficult. The sensors would have to be...

Two vibrators that close should set up some interesting harmonics. Have fun Les, My original K.I.S.S. plan is to have both vibes for the male version driven by the same (PWM) output channel, and make the female vibe be a single, higher power (egg) vibe. My teasing system is complex enough as is. I ...

I think there's an Emacs plugin that can do that. Almost anything worth doing on a computer can be done with Emacs. http://www.youtube.com/watch?v=D1sXuHnf_lo I should have guessed that the above Emacs/Vibe bindings were courtesy of Qdot. For further Emacs humor, you may enjoy http://xkcd.com/378/

well you can always try and make it a limited pre-order thing too. Like you assemple a thing and send it by mail for a certain ammount of money. My problem with this things, however, is that I found vibration doesn't take me nowhere near orgasm, rather it makes my cock numb and almost insensitive. ...

When will this be available? @scoobydome, It's going to be awhile until this is even ready for beta testing. I've just begun putting together a second unit, with some new capabilities for my alpha testers. I expect to go through several iterations of both the hardware and the software during alpha ...

Any reason not to use EMG readings directly within the vagina? (Aside from safety which would have to be taken into account...) @scoobydome, Doing EMG would mean electrical contact with the subject, and doing that safely and to FDA-mandated requirements would add greatly to the complexity and cost....

More progress to report, I've created a successful way for a logic signal (e.g. from an Arduino or similar), to control a Hitachi magic wand. It's a very safe design, using an optically isolated solid state relay; this gives it 4,000 volts isolation between the logic signal and the AC lines. Right ...

PiJoy reading your message again I see you use an anal sensor to measure closeness to orgasm for females. Since I "manually" measure it on my wife via fingers in her vagina, it seems like it would be easy to provide you a lot of very accurate data to tune with. @lemming, Please check your...

So PiJoy, you seem to have all the pieces in place to build the automated teasing machine, at least for a woman. With a bound lady, with the hitachi bound in place, your machine gets us at least 50% of the way there. So then what is required in your mind to take that next step where the machine can...

First off, there are commercial products that can do this. I suggest you search online for VOX or "voice activated switches." However, I understand if cost pushes you in a DIY direction. Doing audio processing on an Arduino by itself may be tricky (unless you use some hacks/tricks), becaus...

that is so annoying! why do they even sell them? @Harrykiles, You may not be into it, but some of us really get off (both figuratively and literally) from teasing and tantalizing! Just as some kinksters are into "good pain" others among us enjoy sensations that you find annoying. Not know...